Einstellhülse Differentiallager-Crush Sleeve / 8" - 28 Spline
  • Einstellhülse Differentiallager-Crush Sleeve / 8" - 28 Spline

8" Rear Axle Crush Sleeve 64-73

3507575 81055(1/2)

64-73 Crush Sleeve – pinion bearing spacer for Ford 8" rear axle

zł31.71
Quantity

Notify me when in stock

Drop your email and we'll let you know the moment it's back.

favorite_border favorite
Description

Crush sleeve (collapsible spacer) for the Ford 8" rear axle in 1964-1973 models. It is installed on the pinion shaft between the two pinion bearings. Its purpose is to ensure correct bearing preload when setting up the ring and pinion gears.

The sleeve must be replaced every time the bearings are replaced or the rear axle is disassembled. Once crushed, it cannot be reused. Replacing only the pinion seal without replacing the sleeve may lead to premature bearing failure.

  • Application: Ford 8" rear axle
  • Years: 1964-1973 (Mustang)
  • Type: Crush Sleeve
Product Details
3507575 81055(1/2)

Data sheet

Year
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973

Specific References

MPN
3507575
64 other products in the same category:
Spring set front axle (289-302) 64-70

Reference: C7ZZ-5310-B 4127513(x2)

Brand: Mustangclinic Classic Mustang Parts

Front Coil Springs, Small Block, Standard, 1964-1970 Mustang

favorite_border favorite
64-70 suspension springs for 289 302 351W V8 engines. If needed, they can be cut to lower the front of the car. Especially on 65-66 models, a typical cut is 0.5-0.75 of a coil
zł730.89
More Front Coil Springs, Small Block, Standard, 1964-1970 Mustang
Out-of-Stock
Front Coil Springs, Stiffer, Small Block Ford Mustang 1964–1970 Front Coil Springs, Stiffer, Small Block Ford Mustang 1964–1970

Reference: C7ZZ-5310-P

Brand: Scott Drake

Front Coil Springs, Stiffer, Small Block 64-70

favorite_border favorite
64-70 suspension coil springs for 289-351 V8 engines. Lowered 1 inch, but made from thicker wire, so the final ride height is close to stock. Stiffer, they keep the car planted on the road. The handling feels closer to that of modern cars.
zł545.53
More Front Coil Springs, Stiffer, Small Block 64-70
Out-of-Stock
Ford 8" Rear Axle Ring and Pinion Gear Set 3.55 Ratio USA Standard Gear Ford Mustang 1964–1973

Reference: ZG F8-355

Brand: Mustangclinic Classic Mustang Parts

Ford 8" Rear Axle Ring and Pinion Gear Set 3.55 Ratio USA Standard Gear

favorite_border favorite
High-quality 8-inch rear axle gear set, made in the USA. The 3.55 ratio is ideal when converting to an AOD or T5 transmission (also called gearbox). With a standard 4-speed or C4/C6 transmission you get more power in the lower gears, but at the cost of high engine RPM at speeds above 90 km/h.
zł1,912.20
More Ford 8" Rear Axle Ring and Pinion Gear Set 3.55 Ratio USA Standard Gear
Out-of-Stock
Rear wheel bearing 8" rear axle V8 64-73 Rear wheel bearing 8" rear axle V8 64-73

Reference: WBRW207CCRA

Brand: Mustangclinic Classic Mustang Parts

Rear Axle Bearing V8 64-73 Standard Quality

favorite_border favorite
Rear wheel bearing (rear axle shaft bearing). Standard quality. I recommend the American Timken bearings, which we also offer. However, if you only plan to drive your Mustang a few thousand kilometers, these will be perfectly sufficient.
zł104.88
More Rear Axle Bearing V8 64-73 Standard Quality
In stock

Follow us on Facebook