All best sellers
view_list

Wishlist Products

(0) product

There is no products in wishlist.
  • New
Tailstocks - BigBlock Rocker Arm Conversion Kit
  • Tailstocks - BigBlock Rocker Arm Conversion Kit
  • Tailstocks - BigBlock Rocker Arm Conversion Kit

Tailstocks - BigBlock Rocker Arm Conversion Kit

CRN-52655-16

Solid, tested on engines built by us.

zł1,100.00
Tax included
Quantity
Last items in stock

favorite_border favorite
Description

Dimensions:

7/16-20" pins

5/16" Push Rod Guide Plates

Set of 16 pieces

Product Details
CRN-52655-16
CRN-52655-16

Data sheet

Year
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
64 other products in the same category:

Reference: ARP-154-3603

ARP Ford 351W head bolts.

favorite_border favorite
64-73 Head bolts for Small Block Windsor engines. Fits for standard heads and Edelbrock Performer RPM .
zł678.00
More ARP Ford 351W head bolts.
In stock

Reference: CCA-235

Engine parts, mix needed when assembling Small Block 64-73

favorite_border favorite
64-73 Engine parts kit includes: . Timing bolt, head guide bushings, shaft wedge, two-piece fuel pump drive, etc. . Parts fit 260 289 302 351W . Note the fuel pump drive is two-piece, requires the corresponding timing chain of newer type .
zł244.00
More Engine parts, mix needed when assembling Small Block 64-73
In stock

Reference: WL-6065C

Ignition cable routing 7-9mm 64-73

favorite_border favorite
64-73 Ignition wire separator, attached to valve caps, designed for Ford 289, 302, 351W engines. Fits for 7 to 9 mm diameter cables. Requires longer cables or universal cables cut to fit perfectly .
zł335.00
More Ignition cable routing 7-9mm 64-73
Last items in stock

Reference: JV611 40509

One-piece crankshaft seal 351W

favorite_border favorite
Solution to the incessant oil leakage from the rear bed of Small Block 351W engines. It is possible to replace the two-piece shaft seal with a one-piece seal. Block machining is required. It is best when doing an engine overhaul to prepare the rear bed for this Siemerring right away. .
zł95.00
More One-piece crankshaft seal 351W
In stock

Reference: U1173 49030

Classic V8 1.5-Ohm ignition coil 64-73

favorite_border favorite
64-73 High-quality coil, a replacement for the standard coil, for instruments with classic platens. The coil requires leaving the classic resistance wire with which every Mustang is equipped. If the electrical system is universal, use a resistor .
zł307.00
More Classic V8 1.5-Ohm ignition coil 64-73
In stock

Reference: 2472

Cap 3/ 8-18 NPT/ 9.5mm

favorite_border favorite
A plug needed here and there ;-) especially for modifications. Self-sealing thread after NPT taper.
zł23.00
More Cap 3/ 8-18 NPT/ 9.5mm
In stock

Reference: 10152

Lucas engine assembly grease 118ml 64-73

favorite_border favorite
64-73 Specialized assembly lubricant to prevent dry starts of a newly built engine. Designed for the assembly of all components such as pan, camshafts, pushrods and pistons. It leaves a protective layer for a long time to prevent friction. One tube is easily enough for the entire V8 engine .
zł28.00
More Lucas engine assembly grease 118ml 64-73
In stock

Reference: PBH-5000

Brand: Power By The Hour Performance

Coyote Gen1 Control Pack Swap from Mustang 2011-14, 64-73

favorite_border favorite
. The easiest and practically the only solution to swap an engine from a new Mustang or F150 to any car. Comes with a new harness, new computer without security and all new sensors or gas pedal. It will work with manual and automatic. For automatic you need to use the old transmission harness or buy a modified one from us. In fact, you only need 3 +/-...
zł13,245.00
More Coyote Gen1 Control Pack Swap from Mustang 2011-14, 64-73
Out-of-Stock

Follow us on Facebook